Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
Right here below yow will discover a lot of sound facts when it comes to Tools You Need to Install a New Bathtub .
Setting up a tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately tough project. If the old tub is readily accessible, the task can relocate speedily; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will require a helper to move out the old bathtub as well as embeded in the new one. Ensure you have actually certified yourself for the job and also fit trying it. Rather than hiring a professional to take control of a halfway-completed project, it is far better to consider using one before you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will aid you mount a new bathtub in your washroom if you have actually already purchased a brand-new tub and do not need to transform the plan of your previous supply of water pipelines.
Your devices and also product list ought to consist of the following:
Planning for the Installment
First of all, the sustaining structure supplied with the bath must be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the limited access that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, place the tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other tap.
Switch on the water system as well as inspect all joints as well as brand-new pipework for leakages and tighten them if needed. Fill up the bath tub and additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bath tub ought to wait up until the bathtub has been made use of at least once as this will certainly resolve it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet ports. The previous type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, triggering the water to pass through the wall in between the bathroom and the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can split relatively very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads on A Step-by-Step Guide to Installing a Bathtub, I thought sharing that article was essential. Sharing is nice. Helping people is fun. Thank you for your time. Come back soon.
Get relief now! Report this page